2.236
Bearbeitungen
Änderungen
Konfiguration (Asus/Yakumo) (Quelltext anzeigen)
Version vom 9. Februar 2007, 10:43 Uhr
, 10:43, 9. Feb. 2007→USB
=== USB ===
=== USB ===
Grundpakete installieren (Driver)
<pre>
<pre>
ipkg install kmod-usb-ohci
ipkg install kmod-usb2
ipkg install kmod-usb-storage
ipkg install kmod-usb-core
ipkg install kmod-usb-core
ipkg install kmod-usb2
ipkg install kmod-vfat
ipkg install kmod-usb-storage
</pre>
Scanner oder Drucker über das Netzwerk nutzen
<pre>
ipkg install kmod-usb-scanner
ipkg install kmod-usb-printer
ipkg install kmod-usb-printer
</pre>
danach Neustart und überprüfen ob das usb Gerät erkannt wurde indem wir
<pre>
dmesg
</pre>
eigeben. Da sollte dann sowas stehen wie:
<pre>
root@dave_yakumo:~# dmesg
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x000b5fec-0x00180000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x00180000-0x003f0000 : "OpenWrt"
diag boardtype: 0000041a
Probing device eth0: No Robo switch in managed mode found
Probing device eth1: No Robo switch in managed mode found
Probing device eth2: No such device
Probing device eth3: No such device
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
eth2: Broadcom BCM4320 802.11 Wireless Controller 3.90.37.0
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2
usb-ohci.c: usb-00:04.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
SCSI subsystem driver Revision: 1.00
hub.c: new USB device 00:04.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x126f/0x1325) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: USB 2.0 Model: Mobile Disk Rev:
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 253952 512-byte hdwr sectors (130 MB)
sda: Write Protect is off
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
</pre>
interessant ist für uns eigentlich nur "Gerät erkannt"
<pre>
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 253952 512-byte hdwr sectors (130 MB)
sda: Write Protect is off
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
</pre>
na dann nur noch mounten
<pre>
</pre>
</pre>