Dave's Web-Log
Steuerbare-Webcam(Logitech Quickcam Orbit/Sphere) unter Linux
zuerst nachsehen mit lsusb
Bus 004 Device 003: ID 046d:08b5 Logitech, Inc.
1. module-assistant installieren - apt-get install module-assistant
2. pwc Webcamdriver - installieren
- module-assistant starten
- PREPARE
- SELECT
- pwc mit leertaste anhaken
- GET - Pakete holen
- BUILD
- INSTALL
3. apache2 installieren - apt-get install apache2
4. php5 installieren - apt-get install php5
- in den apache nun noch php einbinden!
- dann die php-module noch kopieren
- in /etc/apache2.conf die zeile mit den.php Endungen, die Auskommentierung entfernen
- cp /etc/apache2/mods-available/php5 /etc/apache2/mods-enable/php5
5. motion installieren - apt-get install motion
- motion.conf bearbeiten
- livecam.htm und control204.php anlegen
- Cambozola Java-Applet runterladen und in /var/www kopieren --> Cambozola
Als erstes mal die ganzen sachen installieren! Wenn schon die PWC-Driver für die Kamera dabei sind, braucht ihr nicht noch die zu kompilieren. Dann kannst du ab dem apache2 anfangen zu installieren.
- Lege unter /var/www eine neue Datei an die livecam.htm heisst.
vi /var/www/livecam.htm
- Kopiere dir diesen Quelltext rein.
<html> <head> <title>Webcam - Pan and Tilt</title> </head> <body text="#000000" bgcolor="#EEF0E0" link="#0000EE" vlink="#551A8B" alink="#FF0000"> <center> <h2>Web Camera - Logitech Sphere - Pan and Tilt</h2> <applet code=com.charliemouse.cambozola.Viewer archive=cambozola.jar width=320 height=240> <param name=url value=http://Deine_IP_Adresse:8081> </applet> </center> <form name="pantilt" action="control204pt.php" method="post"> <center> Click buttons below to rotate and tilt camera.<br> <INPUT TYPE=SUBMIT NAME="command" VALUE="Pan Left "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" L5 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" L4 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" L3 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" L2 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" L1 "> <INPUT TYPE=SUBMIT NAME="command" VALUE="Center Pan"> <INPUT TYPE=SUBMIT NAME="command" VALUE=" R1 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" R2 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" R3 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" R4 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" R5 "> <INPUT TYPE=SUBMIT NAME="command" VALUE="Pan Right"><br> <INPUT TYPE=SUBMIT NAME="command" VALUE="Tilt Down"> <INPUT TYPE=SUBMIT NAME="command" VALUE=" D5 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" D4 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" D3 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" D2 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" D1 "> <INPUT TYPE=SUBMIT NAME="command" VALUE="Center Tilt"> <INPUT TYPE=SUBMIT NAME="command" VALUE=" U1 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" U2 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" U3 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" U4 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" U5 "> <INPUT TYPE=SUBMIT NAME="command" VALUE=" Tilt Up "><br> <INPUT TYPE=SUBMIT NAME="command" VALUE="Calibrate"> </center> </form> </body> </html>
- unter Deine_IP_Adresse müsst ihr natürlich eure IP eintragen
- als nächstes legen wir die Steuerungsdatei an mit
vi /var/www/control204pt.php
- und dann kopiere dir diesen Quelltext rein
<? Header("HTTP/1.0 204 No Content"); $command = (IsSet($_REQUEST['command'])) ? $_REQUEST['command'] : ""; switch ($command) { case " L5 ": readfile('http://username:password@localhost:8080/0/track/set?pan=-200&tilt=0'); break; case " L4 ": readfile('http://username:password@localhost:8080/0/track/set?x=-60&y=1000'); break; case " L3 ": readfile('http://username:password@localhost:8080/0/track/set?x=-45&y=1000'); break; case " L2 ": readfile('http://username:password@localhost:8080/0/track/set?x=-30&y=1000'); break; case " L1 ": readfile('http://username:password@localhost:8080/0/track/set?x=-15&y=1000'); break; case "Center Pan": readfile('http://username:password@localhost:8080/0/track/set?x=0&y=1000'); break; case " R1 ": readfile('http://username:password@localhost:8080/0/track/set?x=15&y=1000'); break; case " R2 ": readfile('http://username:password@localhost:8080/0/track/set?x=30&y=1000'); break; case " R3 ": readfile('http://username:password@localhost:8080/0/track/set?x=45&y=1000'); break; case " R4 ": readfile('http://username:password@localhost:8080/0/track/set?x=60&y=1000'); break; case " R5 ": readfile('http://username:password@localhost:8080/0/track/set?pan=200&tilt=0'); break; case " U5 ": readfile('http://username:password@localhost:8080/0/track/set?pan=0&tilt=100'); break; case " U4 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=20'); break; case " U3 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=15'); break; case " U2 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=10'); break; case " U1 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=5'); break; case "Center Tilt": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=0'); break; case " D1 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=-5'); break; case " D2 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=-10'); break; case " D3 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=-15'); break; case " D4 ": readfile('http://username:password@localhost:8080/0/track/set?x=1000&y=-20'); break; case " D5 ": readfile('http://username:password@localhost:8080/0/track/set?pan=0&tilt=-100'); break; case "Pan Left ": readfile('http://username:password@localhost:8080/0/track/set?pan=-10&tilt=0'); break; case "Pan Right": readfile('http://username:password@localhost:8080/0/track/set?pan=10&tilt=0'); break; case " Tilt Up ": readfile('http://username:password@localhost:8080/0/track/set?pan=0&tilt=5'); break; case "Tilt Down": readfile('http://username:password@localhost:8080/0/track/set?pan=0&tilt=-5'); break; case "Calibrate": readfile('http://username:password@localhost:8080/0/config/set?text_left=CAMERA%20CALIBRATING%20POSITION'); readfile('http://username:password@localhost:8080/0/detection/pause'); readfile('http://username:password@localhost:8080/0/track/set?x=-69&y=24'); sleep(5); readfile('http://username:password@localhost:8080/0/track/set?x=69&y=-29'); sleep(3); readfile('http://username:password@localhost:8080/0/track/set?x=65&y=-5'); sleep(2); readfile('http://username:password@localhost:8080/0/config/set?text_left=CAMERA'); readfile('http://username:password@localhost:8080/0/detection/start'); default: break; } ?>
- danach noch die motion.conf datei bearbeiten (hier meine bsp.conf)
# Minimal motion example config file provided by the # Debian motion package - for basic webcam operation. # # You most certainly want to investigate # /usr/share/doc/motion/examples/motion-dist.conf.gz # for further configuration options. Also, refer to the # motion man page and /usr/share/doc/motion/motion_guide.html # for detailed information on configuration options. daemon on quiet on # You may very well need to change this (check with 'dmesg' # after plugging in your webcam) videodevice /dev/video0 # Image size in pixels (valid range is camera dependent) width 320 height 240 framerate 2 quality 85 auto_brightness off # Initial brightness, contrast, hue (NTSC), and saturation # 0 = disabled (valid range 0-255) brightness 0 contrast 0 saturation 0 hue 0 # Encode movies in real-time (install ffmpeg before enabling) ffmpeg_cap_new off # Target base directory for pictures and films # You should probably change this (create dir beforehand) target_dir /tmp jpeg_filename bild # Define a port number (e.g. 8000) to enable the mini-http server # 0 = disabled webcam_port 8081 # Set to 'off' to allow anybody (not just localhost) to view the # webcam via the mini-http server (http://hostname:port) webcam_localhost off webcam_quality 50 webcam_maxrate 8 # Drivertyp der Steuerung track_type 3 #Steuerungs-Port control_port 8080
- Links:
- die Dateien stammen alle von Kenneth Lavrsen und wurden leicht modifiziert
- viel spass!
- Motion-Programm --> Motion-Wiki
Steuerbare-Webcam(Logitech Quickcam Orbit/Sphere MP) unter Linux
zuerst nachsehen mit lsusb
Bus 005 Device 008: ID 046d:08cc Logitech, Inc.
dann uvcvideo driver installieren
cd ~ apt-get install subversion linux-headers-`uname -r` svn checkout svn://svn.berlios.de/linux-uvc/linux-uvc/trunk cd trunk vi Makefile -> in der zeile: INSTALL_MOD_DIR := usb/media -> dieses neu einfügen : INSTALL_MOD_DIR := kernel/ubuntu/media/usbvideo speichern (mit :wq) und beenden. make make install rmmod uvcvideo modprobe uvcvideo trace=0xffff
leider hat motion kein v4l2 unterstützung, deshalb nehme ich eine neuere Betaversion von Motion:
cd ~ wget http://www.lavrsen.dk/twiki/pub/Motion/MotionRelease3x2x8beta1/motion-3.2.8_beta1.tar.gz tar -xvzf motion-3.2.8_beta1 cd motion-3.2.8_beta1 ./configure make make install
jetzt muss noch der driver-Typ in der motion.conf geändert werden.
# Drivertyp der Steuerung track_type 5
Aldi-Webcam Qtec Webcam 100 Pac207-BCA installieren
nachschauen was los ist :-) also in die console eintippen.
dmesg
da sollte dann so etwas rausgespuckt werden:
drivers/media/video/spca5xx/spca5xx-main.c: USB SPCA5XX camera found. Qtec Webcam 100 Pac207-BCA
als nächstes überprüfen wir noch die usb-meldung
lsusb
da sollte dann so etwas rausgespuckt werden:
ID 093a:2460 Pixart Imaging, Inc.
nun zum driver installieren: 1. in das Verzeichnis wechseln und neusten driver runterladen mit
cd ~ wget http://mxhaard.free.fr/spca50x/Download/gspcav1-20070508.tar.gz
2. jetzt zu root werden und dann noch die nötigen pakete mit apt zum compilieren runterladen
sudo su Password:xxxx apt-get install linux-headers-`uname -r` linux-restricted-modules-`uname -r` build-essential
3. Dann den gspca Quellcode kompilieren. Das linux Material wird unter /usr/src angebracht. Folgende Befehle eingeben: ins Verzeichnis gehen, downgeloadete Quellakten verschieben, den Quellcode auspacken und dann ins Verzeichnis gehen.
cd /usr/src mv ~/gspcav1-20070508.tar.gz . tar xfvz gspcav1-20070508.tar.gz cd gspcav1-20070508
4. Jetzt Variable CC setzen für das gspca makefile. In diesem Fall benutzt Ubuntu edgy Eft GCC 4.1 als Kernelcompiler
export CC=gcc-4.1
5. Einen Link zurück zu Quellcode setzen.
ln -s /usr/src/linux-headers-`uname -r` /lib/modules/`uname -r`/build
6. Jetzt den gspca Quellcode kompilieren, entfernen der alten Treiber, neuen Treiber laden und installieren. Die folgenden Befehle der reihe nach eingeben:
make modprobe -r spca5xx gspca rm -rf /lib/modules/`uname -r`/kernel/drivers/usb/media/gspca* make install modprobe gspca
Fertig!
Philips-Webcam TouCam XS PCVC 820K installieren
nachschauen was los ist :-) also in die console eintippen.
lsusb
da sollte dann so etwas rausgespuckt werden:
OmniVision Technologies, Inc. OV518 WebCam
nun zum driver installieren: 1. in das Verzeichnis wechseln und neusten driver runterladen mit
cd ~ wget http://ovcam.org/ov511/download/2.xx/distros/ov511-2.32.tar.bz2
2. jetzt zu root werden und dann noch die nötigen pakete mit apt zum compilieren runterladen
sudo su Password:xxxx apt-get install linux-headers-`uname -r` linux-restricted-modules-`uname -r` build-essential
3. Dann den ov511 Quellcode kompilieren. Das linux Material wird unter /usr/src angebracht. Folgende Befehle eingeben: ins Verzeichnis gehen, downgeloadete Quellakten verschieben, den Quellcode auspacken und dann ins Verzeichnis gehen.
cd /usr/src mv ~/ov511-2.32.tar.bz2 . bunzip2 ov511-2.32.tar.bz2 tar xfv ov511-2.32.tar cd ov511-2.32
4. Jetzt Variable CC setzen für das ov511 makefile. In diesem Fall benutzt Ubuntu edgy Eft GCC 4.1 als Kernelcompiler
export CC=gcc-4.1
5. Einen Link zurück zu Quellcode setzen.
ln -s /usr/src/linux-headers-`uname -r` /lib/modules/`uname -r`/build
6. Jetzt den ov511 Quellcode kompilieren, entfernen der alten Treiber, neuen Treiber laden und installieren. Die folgenden Befehle der reihe nach eingeben:
make modprobe -r ov511 rm -rf /lib/modules/`uname -r`/kernel/drivers/usb/media/ov511* make install modprobe ovcamchip modprobe ov511 led=0 compress=1
TI Voyage200(TexasInstruments Taschenrechner) Driver und Linksoftware installieren
nachschauen was los ist :-) also in die console eintippen.
lsusb
da sollte dann so etwas rausgespuckt werden:
Bus 002 Device 006: ID 0451:e001 Texas Instruments, Inc. GraphLink
nun zum driver installieren:
- module-assistant starten
- PREPARE
- SELECT
- tidev-modules mit leertaste anhaken
- GET - Pakete holen
- BUILD
- INSTALL
tilibs2 holen und compilieren tilibs2
Programm tilp2 holen und compilieren tilp2
Wetterstation ws2300 unter Linux einrichten
cd ~ wget http://prdownloads.sourceforge.net/open2300/open2300-1.10.tar.gz?download tar -xvzf open2300-1.10.tar.gz cd open2300-1.10 make make install
neue mysql Datenbank anlegen:
- Name: open2300
neuen Benutzer in der Datenbank anlegen:
- Username: open2300
- Passwort: mysql2300
dann in die datenbank open2300 gehen und das script mysql2300.sql importieren und ausführen
Wiki-Vorlagen
- Vorlage:G23-server <-- Variable
- Vorlage:Link-Bild