Webcam-Howto.: Unterschied zwischen den Versionen
Zeile 1: | Zeile 1: | ||
{{TOCRight}} | {{TOCRight}} | ||
+ | == Driver == | ||
es gibt mittlerweile 4 Webcam-Driver von openwrt | es gibt mittlerweile 4 Webcam-Driver von openwrt | ||
− | == spca5xx/spca5xx_LE | + | === spca5xx/spca5xx_LE === |
* Installation: | * Installation: | ||
:Welches Driver-modul ihr braucht kommt auf Eure Kamera an --> [http://mxhaard.free.fr/spca5xx.html Uebersicht] | :Welches Driver-modul ihr braucht kommt auf Eure Kamera an --> [http://mxhaard.free.fr/spca5xx.html Uebersicht] | ||
Zeile 103: | Zeile 104: | ||
also Driver gefunden, Webcam erkannt. Und das mit der Aldi-Cam super! | also Driver gefunden, Webcam erkannt. Und das mit der Aldi-Cam super! | ||
− | + | ||
− | + | === pwc/pwcx === | |
− | ! | + | |
− | + | <pre> | |
− | + | ipkg install http://141.54.160.25/dave/philips-webcam_0.2_mipsel.ipk | |
+ | </pre> | ||
+ | |||
+ | es wird automatisch ein startscript '''/etc/init.d/S90webcam''' angelegt. | ||
+ | |||
+ | <pre> | ||
+ | cd /etc/init.d/ | ||
+ | vi S90webcam | ||
+ | </pre> | ||
+ | |||
+ | <pre> | ||
+ | #!/bin/sh | ||
+ | |||
+ | # unload drivers in case the were loaded | ||
+ | killall camsrv; rmmod pwcx; rmmod pwc; rmmod videodev | ||
+ | |||
+ | # load webcam driver modules (it can be assumed that the USB drivers are compiled into the kernel or were installed & autoloaded) | ||
+ | insmod videodev || exit 1 | ||
+ | insmod pwc || exit 2 | ||
+ | insmod pwcx || exit 3 | ||
+ | |||
+ | sleep 1 | ||
+ | |||
+ | # check if video device was allocated | ||
+ | if [ ! -e /dev/v4l/video0 ]; then exit 4; fi | ||
+ | |||
+ | # motion starten | ||
+ | motion | ||
+ | </pre> | ||
+ | |||
+ | * Projektseiten: | ||
+ | ** [http://www.saillard.org/linux/pwc/ http://www.saillard.org/linux/pwc/] | ||
+ | ** [http://www.smcc.demon.nl/webcam/ http://www.smcc.demon.nl/webcam/] | ||
+ | |||
+ | === ov511 === | ||
+ | <pre> | ||
+ | ipkg install http://141.54.160.25/dave/ov511_0.1_mipsel.ipk | ||
+ | </pre> | ||
+ | * Projektseite: | ||
+ | ** [http://ovcam.org/ov511/ http://ovcam.org/ov511/] | ||
+ | |||
+ | === Quickcam Messenger === | ||
+ | <pre> | ||
+ | ipkg install http://141.54.160.25/dave/qc-usb-messenger-1.6_0.1_mipsel.ipk | ||
+ | </pre> | ||
+ | * Projektseite: | ||
+ | ** [http://home.mag.cx/messenger/ http://home.mag.cx/messenger/] | ||
+ | |||
+ | == Programme == | ||
+ | |||
+ | |||
+ | |||
+ | === SpcaCat === | ||
Installation: | Installation: | ||
<pre> | <pre> | ||
Zeile 117: | Zeile 170: | ||
chmod +x spcacat | chmod +x spcacat | ||
</pre> | </pre> | ||
− | + | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Alle möglichen Einstellungen stehen in der Hilfe | Alle möglichen Einstellungen stehen in der Hilfe | ||
Zeile 199: | Zeile 245: | ||
</pre> | </pre> | ||
− | + | * Projektseite: | |
+ | ** [http://mxhaard.free.fr/index.html http://mxhaard.free.fr/index.html] - spca5xx Driver und Viewer | ||
+ | |||
+ | === Motion === | ||
+ | Installation: | ||
+ | <pre> | ||
+ | ipkg install http://ping02.stura.uni-weimar.de/dave/libjpeg_6b-1_mipsel.ipk | ||
+ | ipkg install http://ping02.stura.uni-weimar.de/dave/motion_3.2.6-1_mipsel.ipk | ||
+ | </pre> | ||
+ | |||
Nun noch die Config-Datei für motion anlegen. | Nun noch die Config-Datei für motion anlegen. | ||
+ | |||
<pre> | <pre> | ||
vi /etc/motion.conf | vi /etc/motion.conf | ||
Zeile 289: | Zeile 345: | ||
</pre> | </pre> | ||
− | + | * Projektseite: | |
− | * | ||
− | |||
** [http://www.lavrsen.dk/twiki/bin/view/Motion/WebHome http://www.lavrsen.dk/twiki/bin/view/Motion/WebHome] - Motion Wiki | ** [http://www.lavrsen.dk/twiki/bin/view/Motion/WebHome http://www.lavrsen.dk/twiki/bin/view/Motion/WebHome] - Motion Wiki | ||
− | == | + | === Camsrv === |
− | + | === Mvc === | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | == | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | == | ||
− | |||
− | |||
− | |||
− | |||
− |
Version vom 11. März 2007, 18:14 Uhr
Driver
es gibt mittlerweile 4 Webcam-Driver von openwrt
spca5xx/spca5xx_LE
- Installation:
- Welches Driver-modul ihr braucht kommt auf Eure Kamera an --> Uebersicht
# spca5xx-Modul ipkg install http://ping02.stura.uni-weimar.de/dave/kmod-spca5xx_2.4.30+20060501-brcm-1_mipsel.ipk # spca5xx/LE-Modul cd /tmp wget http://ping02.stura.uni-weimar.de/dave/spca5xx_lite.o.gz mv spca5xx_lite.o.gz /lib/modules/2.4.30 cd /lib/modules/2.4.30/ gunzip spca5xx_lite.o.gz
nun noch video-modul und .jpg unterstützung laden
ipkg install libpthread ipkg install kmod-videodev
danach Neustart.
Die Module leider nicht beim Neustart selbstständig geladen.
Webcammodule laden mit
insmod videodev insmod spca5xx oder insmod spca5xx_lite
mit dem Befehl:
lsmod
kannst du überprüfen welche module geladen sind. Jetzt noch überprüfen ob die Webcam erkannt wurde indem wir
dmesg
eigeben. Da sollte dann sowas stehen wie:
root@dave_yakumo:~# dmesg Creating 5 MTD partitions on "Physically mapped flash": 0x00000000-0x00040000 : "cfe" 0x00040000-0x003f0000 : "linux" 0x000b5fec-0x00180000 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x003f0000-0x00400000 : "nvram" 0x00180000-0x003f0000 : "OpenWrt" diag boardtype: 0000041a Probing device eth0: No Robo switch in managed mode found Probing device eth1: No Robo switch in managed mode found Probing device eth2: No such device Probing device eth3: No such device BFL_ENETADM not set in boardflags. Use force=1 to ignore. eth2: Broadcom BCM4320 802.11 Wireless Controller 3.90.37.0 usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2 usb-ohci.c: usb-00:04.0, PCI device 14e4:4715 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected SCSI subsystem driver Revision: 1.00 Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. uhci.c: USB Universal Host Controller Interface driver v1.1 Linux video capture interface: v1.00 usb.c: registered new driver spca5xx drivers/usb/spca5xx.c: spca5xx driver 00.57.07 registered hub.c: new USB device 00:04.0-1, assigned address 2 drivers/usb/spca5xx.c: USB SPCA5XX camera found. Qtec Webcam 100 Pac207-BCA drivers/usb/spca5xx.c: [spca5xx_probe:8380] Camera type GBRG drivers/usb/pac207.h: [pac207_config:148] Find Sensor PAC207 drivers/usb/spca5xx.c: [spca5xx_getcapability:2207] maxw 352 maxh 288 minw 160 minh 120
interessant ist für uns eigentlich nur "Gerät erkannt"
usb.c: registered new driver spca5xx drivers/usb/spca5xx.c: spca5xx driver 00.57.07 registered hub.c: new USB device 00:04.0-1, assigned address 2 drivers/usb/spca5xx.c: USB SPCA5XX camera found. Qtec Webcam 100 Pac207-BCA drivers/usb/spca5xx.c: [spca5xx_probe:8380] Camera type GBRG drivers/usb/pac207.h: [pac207_config:148] Find Sensor PAC207 drivers/usb/spca5xx.c: [spca5xx_getcapability:2207] maxw 352 maxh 288 minw 160 minh 120
also Driver gefunden, Webcam erkannt. Und das mit der Aldi-Cam super!
pwc/pwcx
ipkg install http://141.54.160.25/dave/philips-webcam_0.2_mipsel.ipk
es wird automatisch ein startscript /etc/init.d/S90webcam angelegt.
cd /etc/init.d/ vi S90webcam
#!/bin/sh # unload drivers in case the were loaded killall camsrv; rmmod pwcx; rmmod pwc; rmmod videodev # load webcam driver modules (it can be assumed that the USB drivers are compiled into the kernel or were installed & autoloaded) insmod videodev || exit 1 insmod pwc || exit 2 insmod pwcx || exit 3 sleep 1 # check if video device was allocated if [ ! -e /dev/v4l/video0 ]; then exit 4; fi # motion starten motion
ov511
ipkg install http://141.54.160.25/dave/ov511_0.1_mipsel.ipk
- Projektseite:
Quickcam Messenger
ipkg install http://141.54.160.25/dave/qc-usb-messenger-1.6_0.1_mipsel.ipk
- Projektseite:
Programme
SpcaCat
Installation:
cd /tmp wget http://ping02.stura.uni-weimar.de/dave/spcacat.gz mv spcacat.gz /usr/bin cd /usr/bin gunzip spcacat.gz chmod +x spcacat
Alle möglichen Einstellungen stehen in der Hilfe
spcacat -h
spcacat [-h -d -g -f -s -p -N -P -o] -h show this usage message. -d device ask the driver to use specified video output device (/dev/video1) -o outputfile causes the program to output avi with image data received from the video device to the specified file. -g grab with READ method instead of default MMAP -f video format nothing YUV420P fourcc I420 jpg JPEG fourcc MJPG yuv YUV420P fourcc I420 r16 RGB565 16bits fourcc RGB2 r24 RGB 24bits fourcc RGB3 r32 RGB 32bits fourcc RGB4 -v RAW data fourcc RAWD -s widthxheight ask the driver for input size -p X take a picture every X seconds -p X && -o getPicture every X seconds and record in SpcaPict.jpg -N take N pictures and stop -P parport device (spcacat, spcaserv)
jetzt Link noch legen, weil das Programm das device /dev/v4l/video0 nicht verarbeiten kann. und dann spcacat starten.
ln -s /dev/v4l/video0 /dev/video0 spcacat -d /dev/video0 -g -f jpg -p 10000 -o > /dev/null &
in unserm Falle speichert spcacat aller 10 sek. ein Bild namens SpcaPict.jpg ab.
Eleganter ist es auch diesmal ein script zu erstellen um nicht jedesmal die Module von Hand zu laden. Dazu legt man in dem Startverzeichnis(/etc/init.d) eine Datei z.B. S90webcam an
cd /etc/init.d/ vi S90webcam #!/bin/sh # Variablen Definition REAL="/www/bild.jpg" TEMP="/SpcaPict.jpg" insmod videodev insmod spca5xx sleep 15 # Link legen fuer Vidiodevice ln -s /dev/v4l/video0 /dev/video0 while true do spcacat -d /dev/video0 -g -f jpg -s 320x240 -p 1000 -o > /dev/null & sleep 2 killall spcacat killall -9 spcacat sleep 1 mv $TEMP $REAL sleep 15 done &
berechtigungen noch setzen mit
chmod 0777 S90webcam
- Projektseite:
- http://mxhaard.free.fr/index.html - spca5xx Driver und Viewer
Motion
Installation:
ipkg install http://ping02.stura.uni-weimar.de/dave/libjpeg_6b-1_mipsel.ipk ipkg install http://ping02.stura.uni-weimar.de/dave/motion_3.2.6-1_mipsel.ipk
Nun noch die Config-Datei für motion anlegen.
vi /etc/motion.conf #motion.conf daemon on quiet on # You may very well need to change this (check with 'dmesg' # after plugging in your webcam) videodevice /dev/v4l/video0 # Image size in pixels (valid range is camera dependent) width 320 height 240 quality 60 framerate 1 auto_brightness on # Initial brightness, contrast, hue (NTSC), and saturation # 0 = disabled (valid range 0-255) brightness 0 contrast 0 saturation 0 hue 0 # Target base directory for pictures and films # You should probably change this (create dir beforehand) target_dir /tmp jpeg_filename bild # Define a port number (e.g. 8000) to enable the mini-http server # 0 = disabled webcam_port 8000 # Set to 'off' to allow anybody (not just localhost) to view the # webcam via the mini-http server (http://hostname:port) webcam_localhost off webcam_quality 40 webcam_maxrate 2 # User defined text overlayed on each in the lower left corner text_left "Dave TV"
Und jetzt motion starten mit
motion
Jetzt kann man sich den Stream unter http://IP-Adresse_vom_Router:8000 ansehen
Eleganter ist es auch diesmal ein script zu erstellen um nicht jedesmal die Module von Hand zu laden. Dazu legt man in dem Startverzeichnis(/etc/init.d) eine Datei z.B. S90webcam an
cd /etc/init.d/ vi S90webcam #!/bin/sh # Module laden insmod videodev insmod spca5xx sleep 15 # Link legen fuer Vidiodevice ln -s /tmp/bild.jpg /www/bild.jpg # motion starten while true do motion sleep 900 killall motion killall -9 motion sleep 2 done &
berechtigungen noch setzen mit
chmod 0777 S90webcam
- Projektseite:
- http://www.lavrsen.dk/twiki/bin/view/Motion/WebHome - Motion Wiki