Konfiguration (Asus/Yakumo): Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
(→USB) |
|||
| Zeile 3: | Zeile 3: | ||
=== USB === | === USB === | ||
| + | Grundpakete installieren (Driver) | ||
<pre> | <pre> | ||
| + | ipkg install kmod-usb-ohci | ||
| + | ipkg install kmod-usb2 | ||
| + | ipkg install kmod-usb-storage | ||
ipkg install kmod-usb-core | ipkg install kmod-usb-core | ||
| − | ipkg install kmod- | + | ipkg install kmod-vfat |
| − | ipkg install kmod-usb- | + | </pre> |
| + | |||
| + | Scanner oder Drucker über das Netzwerk nutzen | ||
| + | <pre> | ||
| + | ipkg install kmod-usb-scanner | ||
ipkg install kmod-usb-printer | ipkg install kmod-usb-printer | ||
| − | + | </pre> | |
| + | |||
| + | danach Neustart und überprüfen ob das usb Gerät erkannt wurde indem wir | ||
| + | <pre> | ||
| + | dmesg | ||
| + | </pre> | ||
| + | eigeben. Da sollte dann sowas stehen wie: | ||
| + | <pre> | ||
| + | root@dave_yakumo:~# dmesg | ||
| + | Creating 5 MTD partitions on "Physically mapped flash": | ||
| + | 0x00000000-0x00040000 : "cfe" | ||
| + | 0x00040000-0x003f0000 : "linux" | ||
| + | 0x000b5fec-0x00180000 : "rootfs" | ||
| + | mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only | ||
| + | 0x003f0000-0x00400000 : "nvram" | ||
| + | 0x00180000-0x003f0000 : "OpenWrt" | ||
| + | diag boardtype: 0000041a | ||
| + | Probing device eth0: No Robo switch in managed mode found | ||
| + | Probing device eth1: No Robo switch in managed mode found | ||
| + | Probing device eth2: No such device | ||
| + | Probing device eth3: No such device | ||
| + | BFL_ENETADM not set in boardflags. Use force=1 to ignore. | ||
| + | eth2: Broadcom BCM4320 802.11 Wireless Controller 3.90.37.0 | ||
| + | usb.c: registered new driver usbdevfs | ||
| + | usb.c: registered new driver hub | ||
| + | usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2 | ||
| + | usb-ohci.c: usb-00:04.0, PCI device 14e4:4715 | ||
| + | usb.c: new USB bus registered, assigned bus number 1 | ||
| + | hub.c: USB hub found | ||
| + | hub.c: 2 ports detected | ||
| + | SCSI subsystem driver Revision: 1.00 | ||
| + | hub.c: new USB device 00:04.0-1, assigned address 2 | ||
| + | usb.c: USB device 2 (vend/prod 0x126f/0x1325) is not claimed by any active driver. | ||
| + | Initializing USB Mass Storage driver... | ||
| + | usb.c: registered new driver usb-storage | ||
| + | scsi0 : SCSI emulation for USB Mass Storage devices | ||
| + | Vendor: USB 2.0 Model: Mobile Disk Rev: | ||
| + | Type: Direct-Access ANSI SCSI revision: 02 | ||
| + | Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 | ||
| + | SCSI device sda: 253952 512-byte hdwr sectors (130 MB) | ||
| + | sda: Write Protect is off | ||
| + | WARNING: USB Mass Storage data integrity not assured | ||
| + | USB Mass Storage device found at 2 | ||
| + | USB Mass Storage support registered. | ||
| + | </pre> | ||
| + | interessant ist für uns eigentlich nur "Gerät erkannt" | ||
| + | <pre> | ||
| + | Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 | ||
| + | SCSI device sda: 253952 512-byte hdwr sectors (130 MB) | ||
| + | sda: Write Protect is off | ||
| + | WARNING: USB Mass Storage data integrity not assured | ||
| + | USB Mass Storage device found at 2 | ||
| + | USB Mass Storage support registered. | ||
| + | </pre> | ||
| + | na dann nur noch mounten | ||
| + | <pre> | ||
</pre> | </pre> | ||
Version vom 9. Februar 2007, 12:43 Uhr
Zusätliche Software
Das schönste an diesen Gerät sind doch die vielen Erweiterungsmöglichkeiten.
USB
Grundpakete installieren (Driver)
ipkg install kmod-usb-ohci ipkg install kmod-usb2 ipkg install kmod-usb-storage ipkg install kmod-usb-core ipkg install kmod-vfat
Scanner oder Drucker über das Netzwerk nutzen
ipkg install kmod-usb-scanner ipkg install kmod-usb-printer
danach Neustart und überprüfen ob das usb Gerät erkannt wurde indem wir
dmesg
eigeben. Da sollte dann sowas stehen wie:
root@dave_yakumo:~# dmesg Creating 5 MTD partitions on "Physically mapped flash": 0x00000000-0x00040000 : "cfe" 0x00040000-0x003f0000 : "linux" 0x000b5fec-0x00180000 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x003f0000-0x00400000 : "nvram" 0x00180000-0x003f0000 : "OpenWrt" diag boardtype: 0000041a Probing device eth0: No Robo switch in managed mode found Probing device eth1: No Robo switch in managed mode found Probing device eth2: No such device Probing device eth3: No such device BFL_ENETADM not set in boardflags. Use force=1 to ignore. eth2: Broadcom BCM4320 802.11 Wireless Controller 3.90.37.0 usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xb8004000, IRQ 2 usb-ohci.c: usb-00:04.0, PCI device 14e4:4715 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected SCSI subsystem driver Revision: 1.00 hub.c: new USB device 00:04.0-1, assigned address 2 usb.c: USB device 2 (vend/prod 0x126f/0x1325) is not claimed by any active driver. Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage scsi0 : SCSI emulation for USB Mass Storage devices Vendor: USB 2.0 Model: Mobile Disk Rev: Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sda: 253952 512-byte hdwr sectors (130 MB) sda: Write Protect is off WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 USB Mass Storage support registered.
interessant ist für uns eigentlich nur "Gerät erkannt"
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sda: 253952 512-byte hdwr sectors (130 MB) sda: Write Protect is off WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 USB Mass Storage support registered.
na dann nur noch mounten
IDE-Festplatte
FTP-Server
ipkg install vsftpd
Samba-Server
Webcam
es gibt grundsätzlich zwei größere Projekte für Webcam-Driver
pwc/pwcx
ipkg install kmod-pwc
spca5xx/spca5xx_LE
- Installation:
- Die Dateien spca5xx.o.gz und spcacat.gz mit wget auf den Router laden.
mv spca5xx.o.gz /lib/modules/2.4.30 cd /lib/modules/2.4.30/ gunzip spca5xx.o.gz mv spcacat.gz /usr/bin cd /usr/bin gunzip spcacat.gz chmod +x spcacat
ipkg install videodev
webcam.html anlegen
<html><head>
<script language="JavaScript">
<!--
function refreshIt() {
if (!document.images) return;
document.images['SpcaPic'].src = 'SpcaPict.jpg?' + Math.random();
setTimeout('refreshIt()',10000); // refresh every timeout/1000 secs
}
//-->
</script>
</head>
<body onLoad=" setTimeout('refreshIt()',5000)">
<br><br><br>
<center>
<img src="SpcaPict.jpg" name="SpcaPic">
<br>
Bild wird aller 10 sek. neu geladen
</center>
</body></html>
- Projektseite: